Linkstation Live (LS-CHL-V2)

In Computer und Netzwerk Linkstation Live (LS-CHL) V1, V2 und V3 | Erstellt: 18.10.2010, 18:34 | Editiert: 25.10.2018, 16:42 | 11.328 mal angesehen | Seite drucken

Technische Daten und Bilder der "Buffalo Linkstation Live V2", die mit dem ursprünglich "roten" Web-Interface.

Übersicht

  • CPU: "ARM926EJ-S rev 1 (v5l)", 88F6281 A0 LE, 600MHz
  • RAM: 64MB
  • LAN: 2x GBit, eth0 nicht nach aussen geführt, eth1 "aktives" Interface
  • Platte: 2TB Samsung

cat /proc/cpuinfo

Processor       : ARM926EJ-S rev 1 (v5l)
BogoMIPS        : 599.65
Features        : swp half thumb fastmult edsp
CPU implementer : 0x56
CPU architecture: 5TE
CPU variant     : 0x2
CPU part        : 0x131
CPU revision    : 1
Cache type      : write-back
Cache clean     : cp15 c7 ops
Cache lockdown  : format C
Cache format    : Harvard
I size          : 16384
I assoc         : 4
I line length   : 32
I sets          : 128
D size          : 16384
D assoc         : 4
D line length   : 32
D sets          : 128

Hardware        : Feroceon-KW
Revision        : 0000
Serial          : 0000000000000000

cat /proc/meminfo

MemTotal:        60856 kB
MemFree:          3984 kB
Buffers:          9728 kB
Cached:          12948 kB
SwapCached:          0 kB
Active:          22200 kB
Inactive:         9964 kB
SwapTotal:     2104472 kB
SwapFree:      2103864 kB
Dirty:              28 kB
Writeback:           0 kB
AnonPages:        9504 kB
Mapped:           9056 kB
Slab:            21456 kB
SReclaimable:    12796 kB
SUnreclaim:       8660 kB
PageTables:        752 kB
NFS_Unstable:        0 kB
Bounce:              0 kB
CommitLimit:   2134900 kB
Committed_AS:    43580 kB
VmallocTotal:   581632 kB
VmallocUsed:     17744 kB
VmallocChunk:   557052 kB

dmesg

Linux version 2.6.22.18-88f6281 (root@build2.dd-hot24.nas.buffalo.local) (gcc version 4.2.0 20070413 (prerelease)) #50 Tue Dec 22 18:06:23 JST 2009
CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 16384
  DMA zone: 128 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 16256 pages, LIFO batch:3
  Normal zone: 0 pages used for memmap
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists.  Total pages: 16256
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,12M panic=5 BOOTVER=0.10
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB 0MB 0MB 0MB = 64MB total
Memory: 48376KB available (3772K code, 301K data, 124K init)
Calibrating delay loop... 599.65 BogoMIPS (lpj=2998272)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size  64MB 
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e8000000, size 128MB 
PEX0_IO ....base f2000000, size   1MB 
INTER_REGS ....base f1000000, size   1MB 
NFLASH_CS ....base fa000000, size   2MB 
SPI_CS ....base f4000000, size  16MB 
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size   2MB 

  Marvell Development Board (LSP Version KW_LSP_4.2.6)-- MVLSXL  Soc: 88F6281 A0 LE

 Detected Tclk 166666667 and SysClk 300000000 
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c1426600
PEX0 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
SCSI subsystem initialized
NET: Registered protocol family 2
Time: kw_clocksource clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 12288K
RTC registered
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.1.00 installed.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
Use the XOR engines (acceleration) for enhancing the following functions:
  o RAID 5 Xor calculation
  o kernel memcpy
  o kenrel memzero
Number of XOR engines to use: 4
cesadev_init(c0011e38)
MV Buttons Driver Load
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
SGI XFS with ACLs, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
io scheduler noop registered
io scheduler anticipatory registered (default)
RAMDISK driver initialized: 2 RAM disks of 32768K size 1024 blocksize
loop: module loaded
Loading Marvell Ethernet Driver:
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o Single RX Queue support - ETH_DEF_RXQ=0
  o Single TX Queue support - ETH_DEF_TXQ=0
  o Receive checksum offload enabled
  o Transmit checksum offload enabled
  o Network Fast Processing (Routing) supported
  o Driver ERROR statistics enabled
  o Driver INFO statistics enabled
  o Proc tool API enabled
  o Rx descripors: q0=128
  o Tx descripors: q0=532
  o Loading network interface(s):
    o eth0, ifindex = 1, GbE port = 0
    o eth1, ifindex = 2, GbE port = 1

mvFpRuleDb (c135b000): 1024 entries, 4096 bytes
Integrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access     Hitachi  HDS722020ALA330  JKAO PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 3907029168 512-byte hardware sectors (2000399 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 10 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] 3907029168 512-byte hardware sectors (2000399 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 10 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
 sda: sda1 sda2 sda4 < sda5 sda6 >
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
SPI Serial flash detected @ 0xf4000000, 512KB (8sec x 64KB)
NAND init: NAND device not found on board
mice: PS/2 mouse device common for all mice
Linux telephony interface: v1.00
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1     55 MB/s
raid6: int32x2     65 MB/s
raid6: int32x4     65 MB/s
raid6: int32x8     57 MB/s
raid6: using algorithm int32x2 (65 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
   arm4regs  :   544.800 MB/sec
   8regs     :   379.200 MB/sec
   32regs    :   452.400 MB/sec
raid5: using function: arm4regs (544.800 MB/sec)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Couldn't find valid RAM disk image starting at 0.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Freeing init memory: 124K
Warning: unable to open an initial console.
Adding 2104472k swap on /dev/sda5.  Priority:-1 extents:1 across:2104472k
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: started
eth1: link down
eth1: started
eth1: link up, full duplex, speed 1 Gbps

fw_printenv

Warning: Bad CRC, using default environment
bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm
bootdelay=5
baudrate=115200

U-Boot lädt uImage.buffalo als Kernel, aber entweder fw_printenv hat einen Fehler oder das U-Boot-Environment hat einen Hau weg. Es funktioniert, es wird nichts angefasst, und ein cat /proc/cmdline ergibt:

console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,12M panic=5 BOOTVER=0.10

cat /proc/buffalo/board_info

BoardId=84
BoardName=MVLSXL

cat /proc/buffalo/firmware

SERIES=LinkStation
PRODUCTNAME=LS-CHL-V2(YURYAKU)
VERSION=0.16
SUBVERSION=FLASH 0.00
PRODUCTID=0x00000012
BUILDDATE=2009/12/22 18:06:07
BOOTVER=0.10

Die Informationen und Control-Dateien in /proc/buffalo/ sind nur mit einem “Stock”-Kernel einer Buffalo-Firmware verfügbar. Bei mir

uname -a

Linux linkstation 2.6.22.18-88f6281 #50 Tue Dec 22 18:06:23 JST 2009 armv5tejl GNU/Linux

Mehr Info auf der Seite Debian-Installation.

Bilder

Merkmale von aussen:

  • "Buffalo"-Schriftzug auf den Seiten in schwarz geprägt
  • Mit dem Gehäuse bündige USB- und LAN-Buchse
  • Zweizeiliger Seriennummern-Aufkleber mit Barcode auf der Unterseite

Weitere Seiten in 'Linkstation Live (LS-CHL) V1, V2 und V3'

Schreibe einen Kommentar

Captcha * Time limit is exhausted. Please reload CAPTCHA.