- onderka.com - https://www.onderka.com -

FRITZ!Box 7390 dmesg

dmesg einer Firmware-Version 84.04.88, wenn’s interessiert:

FRITZ!Box Fon WLAN 7390-B-xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Linux version 2.6.19.2 (3860) (gcc version 3.4.6) #1 Fri Nov 26 13:16:13 CET 2010
cpu-probe: Manufacturer MIPS
mips-config1: watch registers implemented
mips-config1: MIPS16 implemented
mips-config1: JTAG pressent
mips-config1: TLB size 64
mips-config3: DSP ASE implmented
mips-config3: Vectored interrupts implmented
cpu-type: MIPS24k(e)
[ikan_setup] USB_POWER on
CPU revision is: 0001964c
Determined physical RAM map:
 memory: 06000000 @ 00000000 (usable)
 memory: 01800000 @ 06800000 (usable)
[init_bootmem]
[free_bootmem]
[free_bootmem]
[reserve_bootmem]
On node 0 totalpages: 32768
  DMA zone: 256 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 32512 pages, LIFO batch:7
  Normal zone: 0 pages used for memmap
[request_resource] Kernel code: start 0x10000 < root->start 0x6800000
[request_resource] Kernel data: start 0x293fe8 < root->start 0x6800000
Built 1 zonelists.  Total pages: 32512
Kernel command line: memsize=128 flash_start=0xBF000000 flash_size=16 console=ttyS0,115200n8r 
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU frequency 500.00 MHz
Using 250.000 MHz high precision timer.
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[free_all_bootmem]
Memory: 117376k/122880k available (2575k kernel code, 5464k reserved, 612k data, 152k init, 0k highmem)
Calibrating delay loop... 330.75 BogoMIPS (lpj=661504)
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
NET: Registered protocol family 16
[ikan_mtd_init]
[ikan_mtd_init] flashsize = 0x01000000 Byte 16 MBytes
[ikan_mtd_init] mtd[0] = 0x9F000000,0x9F000000
[ikan_mtd_init] mtd[0] = 0x00000000 - 0x00000000
[ikan_mtd_init] mtd[1] = 0x9F020000,0x9FF00000
[ikan_mtd_init] mtd[1] = 0x00020000 - 0x00f00000
[ikan_mtd_init] mtd[2] = 0x9F000000,0x9F020000
[ikan_mtd_init] mtd[2] = 0x00000000 - 0x00020000
[ikan_mtd_init] mtd[3] = 0x9FF00000,0x9FF80000
[ikan_mtd_init] mtd[3] = 0x00f00000 - 0x00f80000
[ikan_mtd_init] mtd[4] = 0x9FF80000,0xA0000000
[ikan_mtd_init] mtd[4] = 0x00f80000 - 0x01000000
[ikan_mtd_init] mtd[5] = 0x9F000000,0x9F000000
[ikan_mtd_init] mtd[5] = 0x00000000 - 0x00000000
[ikan_mtd_init] mtd0:           filesystem: 0x00000000 - 0x00000000 (size 0x0)
[ikan_mtd_init] mtd1:               kernel: 0x00020000 - 0x00f00000 (size 0xee0000)
[ikan_mtd_init] mtd2:              urlader: 0x00000000 - 0x00020000 (size 0x20000)
[ikan_mtd_init] mtd3:             tffs (1): 0x00f00000 - 0x00f80000 (size 0x80000)
[ikan_mtd_init] mtd4:             tffs (2): 0x00f80000 - 0x01000000 (size 0x80000)
[ikan_mtd_init] mtd5:             reserved: 0x00000000 - 0x00000000 (size 0x0)
[ikan_gpio_init]
Fusiv PCI: starting...
pktsched: using high resolution timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 4096 bind 2048)
TCP reno registered
squashfs: version 3.2 (2007/01/02) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
fuse init (API version 7.8)
yaffs Nov 26 2010 13:15:46 Installing. 
io scheduler noop registered (default)
avm_net_trace: Up and running.
[gpio 13]: VX180_GPIO_POLAR: active low
[gpio 13]: GPIO_EDGE_SENSITIVE
[avm] configured: watchdog event debug enable direct gpio 

AVM_WATCHDOG: Watchdog Driver for AR7 Hardware (Version 1.0, build: Nov 26 2010 13:15:15)
Serial: 8250/16550 driver $Revision: 1.3 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xb90a0000 (irq = 29) is a 16450
[cpmac] Version: 1.108.1.53  -  Revision 811:1136  -  Fr  26.11.2010  13:15:46 
PPP generic driver version 2.4.2
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
physmap platform flash device: 01000001 at 1f000000
physmap-flash.1: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.1: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
[ikan_jffs2_parser_function] mtd_info->name physmap-flash.1 mtd_info->index 0 param=0 p_mtd_pat=0x811e123c
[ikan_jffs2_parser_function] try partition kernel (offset 0x20000 len 15597568)
[ikan_squashfs_parser_function] mtd_info->name physmap-flash.1 mtd_info->index 0 param=0 p_mtd_pat=0x811e123c
[ikan_squashfs_parser_function] *p_mtd_pat->name filesystem
[mtd0]           filesystem: 0x00000000 - 0x00000000 (size 0x0)
[mtd1]               kernel: 0x00020000 - 0x00f00000 (size 0xee0000)
[mtd2]              urlader: 0x00000000 - 0x00020000 (size 0x20000)
[mtd3]             tffs (1): 0x00f00000 - 0x00f80000 (size 0x80000)
[mtd4]             tffs (2): 0x00f80000 - 0x01000000 (size 0x80000)
[mtd5]             reserved: 0x00000000 - 0x00000000 (size 0x0)
[ikan_squashfs_parser_function] try partition kernel (offset 0x20000 len 15597568 blocksize=20000)
[ikan_squashfs_parser_function] magic found @pos 0x127100
[ikan_squashfs_parser_function] flashsize=1000000
[ikan_squashfs_parser_function] jffs2_start@b40000 size: 60
6 find_squashfs partitions found on MTD device physmap-flash.1
Creating 6 MTD partitions on "physmap-flash.1":
0x00127100-0x00f00000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
[ikan_mtd_add_notifier] name rootfs
[ikan_mtd_add_notifier] use rootfs
[ikan_mtd_add_notifier] root device: /dev/mtdblock0 (rootfs)
0x00020000-0x00127100 : "kernel"
mtd: partition "kernel" doesn't end on an erase block -- force read-only
[ikan_mtd_add_notifier] name kernel
[ikan_mtd_add_notifier] skip kernel
0x00000000-0x00020000 : "urlader"
[ikan_mtd_add_notifier] name urlader
[ikan_mtd_add_notifier] skip urlader
0x00f00000-0x00f80000 : "tffs (1)"
[ikan_mtd_add_notifier] name tffs (1)
[ikan_mtd_add_notifier] skip tffs (1)
0x00f80000-0x01000000 : "tffs (2)"
[ikan_mtd_add_notifier] name tffs (2)
[ikan_mtd_add_notifier] skip tffs (2)
0x00b40000-0x00f00000 : "jffs2"
[ikan_mtd_add_notifier] name jffs2
[ikan_mtd_add_notifier] skip jffs2
Generic platform RAM MTD, (c) 2004 Simtec Electronics
[request_resource] mtd-ram: start 0x1e000000 < root->start 0x1f000000
mtd-ram mtd-ram.2: failed to request memory region
[ikan_ram_mtd_set_rw] PLATRAM_RO
mtd-ram: probe of mtd-ram.2 failed with error -5
AVM Direct NAND driver, © 2008 AVM Berlin
[direct_avm_nand_probe] error output
[NAND] direct NAND: GPIO usage: 16: /CE0 17: /CE1: 20 /WP 18: CLE 19: ALE (0x3)
[direct_avm_nand_probe] irq init
[gpio 21]: VX180_GPIO_POLAR: active high
[gpio 21]: GPIO_EDGE_SENSITIVE
[gpio 7]: VX180_GPIO_POLAR: active high
[gpio 7]: GPIO_EDGE_SENSITIVE
NAND device: Manufacturer ID: 0x20, Chip ID: 0xdc (ST Micro NAND 512MiB 3,3V 8-bit)
NAND device: size write 0x800 oob 0x40 erase 0x20000
Scanning device for bad blocks. <6>Scan first page.
Scan only OOB area.
Check only oob flags.
[direct_avm_nand_adjust_partitions] adjust to size 0x20000000 (536870912)
[direct_avm_nand_adjust_partitions] old size 0x20000000 (536870912)
Creating 1 MTD partitions on "NAND 512MiB 3,3V 8-bit":
0x00000000-0x20000000 : "nand-filesystem"
[ikan_mtd_add_notifier] name nand-filesystem
[ikan_mtd_add_notifier] skip nand-filesystem
CAPI Subsystem Rev 1.1.2.8
ip_conntrack version 2.4 (960 buckets, 7680 max) - 264 bytes per conntrack
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
mcfw: IGMPv3 fast forwarding
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
[TFFS_Init] 1: mtd_number: 3 | mtd_number2: 4
Time: MIPS clocksource has been installed.
[get_mtd_device_wrapped] 1: 3
[get_mtd_device_wrapped] 2
[TFFS_Init] 3
[TFFS_Init] 4.0
[put_mtd_device_wrapped] 1
[put_mtd_device_wrapped] 2
[put_mtd_device_wrapped] 3
[get_mtd_device_wrapped] 1: 4
[get_mtd_device_wrapped] 2
[TFFS_Init] 5
[TFFS_Init] 6
[TFFS_Init] 7
[TFFS_Init] 8
[TFFS_Init] 9
TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 2.0)
      mount on mtd3 and mtd4 (double buffering)
Adam2 environment variables API installed.
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 152k freed
AVM_WATCHDOG: System Init UEberwachung 240 Sekunden
TFFS Name Table G
led_modul_Fritz_Box_7390: module license '
(C) Copyright 2008 by AVM
' taintskernel.
[led_gpio_bit_driver_init] gpio 24 name power
[led_gpio_bit_driver_init] gpio 28 name internet
[led_gpio_bit_driver_init] gpio 26 name festnetz
[led_gpio_bit_driver_init] gpio 27 name wlan
[led_gpio_bit_driver_init] gpio 22 name dual1
[led_gpio_bit_driver_init] gpio 23 name dual2
[button_init] name button_wlan, gpio 31 active_low
[gpio 31]: VX180_GPIO_POLAR: active low
[gpio 31]: GPIO_BOTH_EDGES_SENSITIVE
[button_init] name button_dect, gpio 29 active_low
[gpio 29]: VX180_GPIO_POLAR: active low
[gpio 29]: GPIO_BOTH_EDGES_SENSITIVE
[LED] "wyatt_earp_turn_off_leds" (0x80406610) loaded
fusiv library initializing...

fusiv library initialized SUCCESSFULLY... 

AP2AP fastpath initialized SUCCESSFULLY...

 Added AP PREROUTE Hook 
 Added AP POSTROUTE Hook 
 Buffer Manager is initializing...
BMU GIGE clock 
Slave Mem Alloc: Req size 32   Ptr2Block 0x191f0000
Load into BM APU Successful !!!

Timers are getting initalized
Timers are initilized SUCCESSFULLY...
cpmac0: Netpro Sierra Ethernet found at 0xb9110000, irq 14
Setting unknown egress to SPA
Slave Mem Alloc: Req size 32   Ptr2Block 0x191f0020

Ethernet Driver is initialized SUCCESSFULLY
periApDriverInit: doneSlave Mem Alloc: Req size 32   Ptr2Block 0x191f0040

 *******LOAD firmware to AP:PERI_ID result:0Load into PERI_AP APU Successful !!!


 ACL-AP is initializing...
ACL major allocated is 201
Slave Mem Alloc: Req size 32   Ptr2Block 0x191f0060
Configuring host ACL Layer-2 ruleset (128/4 Rules/Intf)
Intf	Addr
0	00454000
1	00454e00
2	00455c00
3	00456a00
Configuring host ACL Layer-3 ruleset (128/4 Rules/Intf)
Intf	Addr
0	00468000
1	00468e00
2	00469c00
3	0046aa00
Load into ACL_AP APU Successful !!!

Need to run mknod ...
***** VDSL BME driver registered with Major number: 254 *****
Request Region 0xa6000000 - 0xa67fffff 
Region 0xa6000000 - 0xa67fffff allocated successfully
[piglet]use gpio-settings for 156
patch_dectfw: c10db000, totallen = 47136(b820)
patch_dectfw: patch_adress: f0ff8 max_len: 26 with Version 2 Len: 17
dect_loader: fast-bootmode
*
********************************************************************************************
dect144xx_file_process: upload of '/lib/modules/dectfw_secondlevel_488.hex' successfull
[piglet]bitfile '/lib/modules/bitfile.bit'
[piglet] Read 169309 bytes total from file
[piglet] "wyatt_earp_unload_xilinx" loaded
yaffs: dev is 32505862 name is "mtdblock6"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.6, "mtdblock6"
yaffs: restored from checkpoint
yaffs_read_super: isCheckpointed 1

[avm_debug]redirect kernel-messages (/dev/debug)
VDSL PHY default parameters configured successfully
Calling vdslAtmCellHeaderRAMReset()....
default parameters configured successfully
VDSL link parameters set

DSL
---
           CPU0       
  1:          0          <NULL>  arbiter C-Bus
  4:       4209          <NULL>  gpio 16..31
  5:          0          <NULL>  arbiter D-Bus A
  6:          0          <NULL>  UARTDECT_IRQ
  8:          0          <NULL>  gpio 0..15
  9:    4301969          <NULL>  timer
 12:          0          <NULL>  arbiter D-Bus B
 14:      18030          <NULL>  cpmac0
 17:    2140437          <NULL>  INT_FL0_DSP0
 25:    3313074          <NULL>  wifi1, wifi0
 27:          0          <NULL>  arbiter D-Bus C
 28:    2191411          <NULL>  /dev/acl
 29:      17847          <NULL>  serial
 30:          0          <NULL>  peri_ap
 31:       3057          <NULL>  bmap
 35:          0          <NULL>  ehci_hcd:usb1, ohci_hcd:usb2
 36:          7          <NULL>  atmap

ERR:         15
cat: can't open '/proc/avalanche/avsar_*': No such file or directory
exp_pm_mode_L2: 0
exp_pm_mode_L2_act: 0
modem_ShowtimeSecs: 17021
--------- TRAINING FAIL REASON FILE ---------
Sat Jan  1 01:00:30 CET 2000
---------------------------------------------
event=1320 state=8 reason=507.
event=1503 state=2 reason=515.
event=0 state=0 reason=0.
event=0 state=0 reason=0.
event=0 state=0 reason=0.
event=0 state=0 reason=0.
event=0 state=0 reason=0.
event=0 state=0 reason=0.
event=0 state=0 reason=0.
event=0 state=0 reason=0.
------ END OF TRAINING FAIL REASON FILE -----
SUPPORTED_TIOIDINFO_VERSION_NUMBER=4
AVM_DSL_STAT_EVENT_VERSION=5
AVM_DSL_PARAM_INTERFACE_VERSION=4
bme TIOIDINFO size=5376
 kernel TIOIDINFO size=5376