Musicpal dmesg-Log

Zurück zu “Freecom Musicpal”

Die dmesg-Ausgabe beider Modelle. Zuerst “Generation 1″ (Produkt-Code SSRAA):

Linux version 2.6.16.16-88w8xx8 (RnD@freecom.com) (gcc version 3.3.3 (DENX ELDK 3.1.1 3.3.3-9)) #394 PREEMPT Mon Jul 21 09:31:08 UTC 2008
CPU: ARM926EJ-Sid(wb) [41159261] revision 1 (ARMv5TE)
Machine: MV88W8618-HS35
Using U-Boot release 1.1.1.23
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 8192
DMA zone: 8192 pages, LIFO batch:1
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 0 pages, LIFO batch:0
HighMem zone: 0 pages, LIFO batch:0
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists
Kernel command line: console=ttyS0,38400 root=/dev/mtdblock0 ro rootfstype=jffs2 ethaddr=00:01:db:xx:xx:xx
PID hash table entries: 256 (order: 8, 4096 bytes)
Console: colour dummy device 80×30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 32MB = 32MB total
Memory: 29268KB available (2100K code, 911K data, 92K init)
Calibrating delay loop… 175.30 BogoMIPS (lpj=876544)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Reserved 64 pages (page size 4096) starting from c03c0000 for WLAN buffer pool
audio_init, major is 254 …
audioOpen: connected audio IRQ – 30
audio set to DMA mode fc000000 fc001000 2048
Rx c0000000 c000 0
Marvell USB EHCI Host controller
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Successfully initialized LCD driver
mvlcd_init: Successfully allocated a page for video memory.
mvlcd_init: Successfully allocated frame buffer data structures.
Successfully added lcd driver major 253
mvlcd_init: Successfully created proc.
knobcon: major number 252
mv88w8xx8_knobcon_init : Assigned IRQ 12 to knobcon device.
Dynamic Power Management for MV8618.
audit: initializing netlink socket (disabled)
audit(946684800.880:1): initialized
NTFS driver 2.1.26 [Flags: R/O].
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0xf800c840 (irq = 11) is a 16550
RAMDISK driver initialized: 2 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
PHY found at addr 1, ID 1410e20, mii_status 78c9
PHY is 88E3015
eth0: mv88w8xx8 FEC @ 80008000, 00:01:db:08:c7:9a irq 9
Found: SST 39VF6401B
mv88w8xx8 flash: Found 1×16 devices at 0x0 in 16-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 4 MTD partitions on “mv88w8xx8 flash”:
0x00000000-0x00740000 : “LINUX_ROOT_FS”
0x00740000-0x007a0000 : “LINUX_HOME_FS”
0x007a0000-0x007b0000 : “LINUX_MANCONF”
0x007b0000-0x00800000 : “U-BOOT”
usbmon: debugfs is not available
Loading ehci-mv88w8xx8
Inside ehci_mv88w8xx8_probe
ehci-mv88w8xx8 ehci-mv88w8xx8.1436: EHCI Host Controller
ehci-mv88w8xx8 ehci-mv88w8xx8.1436: new USB bus registered, assigned bus number 1
ehci-mv88w8xx8 ehci-mv88w8xx8.1436: irq 8, io mem 0xf8000100
ehci-mv88w8xx8 ehci-mv88w8xx8.1436: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver…
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Mounted root (jffs2 filesystem) readonly.
Freeing init memory: 92K
wlandrv: module license ‘Proprietary’ taints kernel.
WLAN module setup
WLAN mfg partition name is ‘LINUX_MANCONF’ (part num=2)
WLAN domain code = 0x10
WLAN device addr = 00:01:db:xx:xx:xx (from mfg part)
WLAN device name = wlan0
WLAN buffer pool starts from c03c0000 size 0003fc00 (85 * 3072)
RF antenna is turned ON.
audio_open.
audio_open.
Audio device open count: 2.
RF antenna is turned OFF.
RF antenna is turned ON.

Das dmesg eines “MusicPal 2″ (Produkt-Code SSRBA):

JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered
Real Time Clock Driver v0.10
Watchdog Timer Initialized
Storm crypto Initialization
ttySL0 at MMIO 0x42000000 (irq = 18) is a SL2312
RAMDISK driver initialized: 16 RAM disks of 20480K size 1024 blocksize
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
VSC-switch not found
Storm Semiconductors,Inc. SL351x Giga Ethernet driver 0.1.7 built at Oct 5 2009 09:32:10
GMAC Init……
SL2312 MTD Driver Init…….
SL2312 CFI Flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
cfi_fixup: Enter…
cfi_fixup: f->fixup=0xc01c96f8
cfi_fixup: f->fixup=0xc01c9764
cfi_fixup: Enter…
cfi_fixup: f->fixup=0xc01c97b4
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 6 MTD partitions on “SL2312 CFI Flash”:
0x00000000-0x00040000 : “RedBoot”
0x00040000-0x00340000 : “Kernel”
0x00340000-0x00ee0000 : “RootFs”
0x00ee0000-0x00fe0000 : “HomeFs”
0x00fe0000-0x01000000 : “VCTL”
0x00000000-0x01000000 : “Full”
SL2312 MTD Driver Init Success ……
FTC_FOTG2XX : Init FOTG2XX Driver
Init FOTG2xx driver
FTC_FOTG2XX : >>> Found FOTG2XX …
pFTC_OTG c061f540
FTC_FOTG2XX_1 : Init FOTG2XX Driver
Init FOTG2xx driver
FTC_FOTG2XX_1 : >>> Found FOTG2XX …
pFTC_OTG_1 c061f480
hcd->self.controller c3c3fc00
hcd end
hcd_buffer_create
ehci-hcd-FOTG2XX ehci-hcd-FOTG2XX: new USB bus registered, assigned bus number 1
usb_register_bus
ghcd_FOTG2XX hcd c3c3fc00
hcd_irq_For_OTG
ehci->caps->length 10, hcd->regs f6800000 , ehci->regs f6800010
udev->state 1
drivers/usb/host/ehci-hcd-FOTG2XX.c: USB support enabled, EHCI rev 101. 0
Timing on EOF1(0xf6800040) = 0xd
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
FTC_FOTG2XX : >>> +FOTG2XX_get_otg_transceiver
FTC_FOTG2XX : registered host c3c3fc00
OTG2XX act as HOST only (don’t need to wait gadget driver)
+(OTGC_Init)
pFTC_OTG->otg.default_a=1
+(OTGC_Init)
pFTC_OTG->otg.default_a=1
OTG_enable_VBUS
FTC_FOTG2XX : >>> Drive VBUS ok…
+OTGP_Close()
OTG2XX act as HOST only (remove gadget function)
+OTGH_Open()(0x30=0x0)
OTG_enable_VBUS
mdwOTGC_Control_A_VBUS_VLD_Rd 80000
+OTGP_Close()
OTG2XX act as HOST only (remove gadget function)
+OTGH_Open()(0x30=0x0)
ehci otg_set_host status 0
connect_change 1
clear_bit
return set_bit
hcd->self.controller c3c3f400
hcd end
hcd_buffer_create
ehci-hcd-FOTG2XX-1 ehci-hcd-FOTG2XX-1: new USB bus registered, assigned bus number 2
usb_register_bus
ghcd_FOTG2XX_1 hcd c3c3f400
hcd_irq_For_OTG_1
ehci->caps->length 10, hcd->regs f6900000 , ehci->regs f6900010
udev->state 1
drivers/usb/host/ehci-hcd-FOTG2XX-1.c: USB support enabled, EHCI rev 101. 0
Timing on EOF1(0xf6900040) = 0xd
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
FTC_FOTG2XX_1 : >>> +FOTG2XX_get_otg_transceiver_1
FTC_FOTG2XX_1 : registered host c3c3f400
OTG2XX act as HOST only (don’t need to wait gadget driver)
+(OTGC_Init_1)
pFTC_OTG_1->otg.default_a=1
+(OTGC_Init_1)
pFTC_OTG_1->otg.default_a=1
OTG_enable_VBUS
FTC_FOTG2XX_1 : >>> Drive VBUS ok…
+OTGP_Close_1()
OTG2XX act as HOST only (remove gadget function)
+OTGH_Open_1()(0x30=0x0)
OTG_enable_VBUS
mdwOTGC_Control_A_VBUS_VLD_Rd 80000
+OTGP_Close_1()
OTG2XX act as HOST only (remove gadget function)
+OTGH_Open_1()(0x30=0x0)
ehci otg_set_host status 0
connect_change 1
clear_bit
return set_bit
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver…
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ipsec_init : cryptographic accelerator
ipsec tx_desc = ffcb3000
ipsec rx_desc = ffcb4000
ipsec tx_desc_dma = 00752000
ipsec rx_desc_dma = 00753000
Storm I2S of SSP Initialization as /dev/audio
Buffer allocation for SSP!
EQUALIZE: bass=0x0F treble=0x00 dac=0xFF flags=0x03
netem: version 1.1
u32 classifier
Perfomance counters on
input device check on
Actions configured
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
ip_conntrack version 2.4 (512 buckets, 4096 max) – 260 bytes per conntrack
ip_conntrack_pptp version 3.1 loaded
ip_nat_pptp version 3.0 loaded
ip_tables: (C) 2000-2002 Netfilter core team
ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
VFS: Mounted root (jffs2 filesystem) readonly.
Freeing init memory: 104K
NTFS driver 2.1.25 [Flags: R/O MODULE].
Using Marvell 88W3015
GPIO pull register = 0x00E00000
GPIO up/down register = 0x00E00000
GMAC-0 Addr 1 Vendor ID: 0x01410e20
mii_write: phy_addr=0x1 reg_addr=0x4 value=0x5e1
mii_write: phy_addr=0x1 reg_addr=0x16 value=0x4a58
mii_write: phy_addr=0x1 reg_addr=0x19 value=0x3000
mii_write: phy_addr=0x1 reg_addr=0x0 value=0x1200
mii_write: phy_addr=0x1 reg_addr=0x0 value=0x9200
mii_write: phy_addr=0x1 reg_addr=0x0 value=0x1200
Link Up (0x78ed) MII REG 10 = 0x0
MII REG 5 (bit 5:15) = 0x2f
100M/Full
Flow Control Enable.
Writing status 0x0000001B
Storlink eth0 address = 0001DB000497
Enable MAC Flow Control…
sl351x_ipsec_init::Setting up Matching rule
device eth0 entered promiscuous mode
br_stp_recalculate_bridge_id: p->dev->dev_addr[0]-[5]= 0: 1:db: 0: 4:97
usbcore: registered new driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.23:USB Abstract Control Model driver for USB modems and ISDN adapters
EQUALIZE: bass=0x0F treble=0x00 dac=0xFF flags=0x03
EQUALIZE: bass=0x09 treble=0x0A dac=0xF9 flags=0x03

Ähnliches

Seiten und Einträge, gefunden nach Tags.

Hinterlasse einen Kommentar

Deine E-Mail-Adresse wird nicht veröffentlicht. Erforderliche Felder sind markiert *


2 × = acht

Du kannst folgende HTML-Tags benutzen: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

© 2001-2015 onderka.com | Über, impressum und Lizenz | RSS Einträge | RSS Kommentare | 57q @ 0.434s | 348.205 Spammer